How to Make a Charm Bracelet: Step-by-Step Guide

Measure the wrist and add about ½–1 inch (1.5–2.5 cm). Cut a chain with open links to that length, attach a lobster clasp and jump ring to the ends, then add charms with jump rings every 3–5 links. Five to seven charms suit a 7-inch bracelet.
What you need
- Two pairs of chain-nose pliers and flush cutters
- Chain with links large enough for a jump ring to pass through (cable or rolo chain around 4–6 mm links works well)
- A lobster clasp
- Jump rings, 5–7 mm
- 5–10 charms




Step 1: Size the bracelet
Wrap a strip of paper or a soft tape measure around the wrist bone. Add ½ inch for a snug fit or 1 inch for a looser fit. Charms take up room on the inside, so heavily loaded bracelets need the extra inch.
| Wrist | Bracelet length (comfort fit) |
|---|---|
| 5.5 in (14 cm) | 6.5 in (16.5 cm) |
| 6 in (15 cm) | 7 in (18 cm) |
| 6.5 in (16.5 cm) | 7.5 in (19 cm) |
| 7 in (18 cm) | 8 in (20 cm) |
Step 2: Cut the chain and add the clasp
- Subtract the length of the clasp and jump rings (roughly ½ inch) from your total and cut the chain.
- Attach the lobster clasp to one end with a jump ring.
- Add a jump ring, or a short extender chain, to the other end.
Step 3: Plan the charms
Lay the bracelet flat and arrange the charms before attaching anything. Put the largest or most meaningful charm in the center, then work outward, alternating sizes. Leave about an inch near the clasp without charms so it is easy to fasten.
Step 4: Attach the charms
- Open a jump ring by twisting the ends front-to-back.
- Thread on the charm, then the chain link.
- Twist the ring closed until the ends meet with no gap, so the chain cannot slip out.
- Repeat every 3–5 links, attaching all charms to the same side of the chain so they hang evenly.
Step 5: Check and finish
Put the bracelet on and shake your wrist. Every jump ring should be fully closed, charms should not tangle, and the clasp should be easy to reach. Use thicker jump rings (0.8–1 mm wire) for heavier charms.
Other bracelet styles
- Cuff bracelets: hammer, stamp or decorate an open brass cuff; no clasp needed.
- Bangles with charms: slide charms onto an expandable bangle.
- Connector bracelets: link connectors together with jump rings instead of chain.
Frequently asked questions
How many charms should be on a bracelet?
Five to seven for a balanced look on a 7-inch bracelet; up to 15 for a full, jingly style.
What size jump rings for a charm bracelet?
5–7 mm outer diameter, in 0.8 mm (20 gauge) wire or thicker so they stay closed.
What chain is best for a charm bracelet?
A sturdy cable or rolo chain with open links large enough for jump rings.
Shop Charms for Jewelry Making
View all →More jewelry making guides
All guides →
How to Stamp Metal Jewelry: A Beginner's Guide to Stamping Blanks
Metal stamping needs steel letter stamps, a 1–2 lb hammer, a steel bench block and soft-metal blanks like brass or copper. Strike...
Jump Ring Sizes Chart: Gauge, mm and How to Open and Use Jump Rings
Jump rings are sized by outer diameter in mm and wire thickness in gauge or mm. 4–6 mm rings in 0.7–0.8 mm...
Types of Earring Hooks and Ear Wires (and How to Make Your Own)
Fish hooks (French wires) are the most common earring hooks; leverbacks and kidney wires are the most secure; hoops, threaders and shepherd...
