How to Stamp Metal Jewelry: A Beginner's Guide to Stamping Blanks

Place a brass or copper stamping blank on a steel bench block, hold a steel letter stamp straight, and give it one firm strike with a 1–2 lb stamping hammer. Then fill the letters with enamel paint or a permanent marker, wipe the surface, and polish.
What you need
- Metal stamps: hardened steel letter, number and design stamps (usually 1.5–3 mm characters).
- Stamping hammer: a brass-head or steel hammer around 1–2 lb (0.5–1 kg). Heavier hammers make deeper impressions with less effort.
- Steel bench block: a hard, flat surface that does not absorb the blow. Put a rubber block or folded towel under it to reduce noise.
- Stamping blanks in the shape you want.
- Tape (washi or painter's tape) to hold the blank still and act as a line guide.
- Finishing: enamel paint or permanent marker, a polishing pad or fine sandpaper, and optionally a nylon hammer and hole punch.




Which metal blanks are easiest to stamp?
| Metal | Ease | Notes |
|---|---|---|
| Aluminum | Very easy | Light and soft, but scratches easily |
| Copper | Easy | Soft, takes deep clean impressions |
| Raw brass | Easy to medium | Golden, slightly harder than copper; great results |
| Sterling silver | Easy to medium | Premium; stamps beautifully |
| Stainless steel | Hard | Needs a heavy hammer and very good stamps |
| Plated blanks | Medium | Stamping can crack or dull the plating |
Thickness matters too: around 0.8 mm (20 gauge) is the sweet spot. Thinner blanks (0.5 mm) stamp easily but can warp; thicker ones need more force. Check the dimensions in each listing; the last number is the thickness.
How to stamp: step by step
- Plan the text. Write it out and count the characters. Find the center letter so the word is centered on the blank.
- Tape the blank to the bench block, and run a piece of tape along the line where the bottom of the letters should sit.
- Find the stamp's orientation. Most stamps have a mark or logo on the side that faces you. Check it every time.
- Stamp from the center outward. Rest the stamp on the tape guide, hold it straight up, and strike once, firmly. A second hit almost always causes a double image.
- Leave even spacing of about half a letter between characters.
- Peel off the tape and check the impression depth.
Darkening and finishing
- Fill the letters with black enamel paint or a fine permanent marker.
- Let it dry for a minute, then wipe the surface with a polishing pad, fine sandpaper or a little rubbing alcohol on a cloth. The color stays in the letters and comes off the surface.
- If the blank curved during stamping, flatten it with a nylon or rawhide hammer on the bench block.
- Polish the surface, and seal raw brass or copper with jewelry lacquer if you want the shine to last.
Common mistakes and fixes
- Double image: the stamp moved or was hit twice. Strike once and hold the stamp firmly.
- Uneven depth: the stamp was tilted. Keep it vertical and hit in the center of the head.
- Crooked lines: use a tape guide for every letter.
- Warped blank: flatten it with a nylon hammer, or use a thicker blank.
Stamping project ideas
- Name and date tags for necklaces and keychains (add a jump ring)
- Stamped brass cuffs with coordinates or quotes
- Pet ID tags
- Hammered texture earrings: use a ball-peen hammer instead of letters
Frequently asked questions
What hammer is best for metal stamping?
A 1–2 lb brass-head or steel stamping hammer. Avoid ordinary claw hammers; they are unbalanced and damage stamps.
What thickness of blank is best for stamping?
Around 0.8 mm (20 gauge) for most projects.
Can you stamp on brass?
Yes. Raw brass stamps very well and gives a warm golden result. Darken the letters and seal it to keep the contrast.
Shop Stamping Blanks & Metal Tags
View all →More jewelry making guides
All guides →
Jump Ring Sizes Chart: Gauge, mm and How to Open and Use Jump Rings
Jump rings are sized by outer diameter in mm and wire thickness in gauge or mm. 4–6 mm rings in 0.7–0.8 mm...
Types of Earring Hooks and Ear Wires (and How to Make Your Own)
Fish hooks (French wires) are the most common earring hooks; leverbacks and kidney wires are the most secure; hoops, threaders and shepherd...
How to Make a Charm Bracelet: Step-by-Step Guide
A charm bracelet is a chain sized to your wrist plus half an inch, a lobster clasp, and charms attached every few...
